Membrane Water Treatment Equipment
Supplementary membrane and deep treatment equipment for water purification and wastewater reuse projects.
Membrane Water Treatment Equipment for pollution-control projects
Supplementary membrane water treatment equipment, including ultrafiltration, reverse osmosis, nanofiltration, EDI and softening water equipment.
Membrane water treatment equipment is discussed for purification, reuse or laboratory water projects that also need water-quality monitoring or verification.
This supplementary water treatment scope can be discussed when a project requires membrane equipment together with water quality online monitoring, laboratory water systems or discharge verification.
Equipment data from supplied material
This table keeps the equipment values, routes and material options stated in the supplied product material. Selection notes and related-product links elsewhere on the page are website guidance, not added hard specifications.
Huisheng supplied product scope. Final sizing still depends on site conditions, but the values in this table are kept to the supplied material.
| Item | Specification / selection note |
|---|---|
| Product direction | Membrane Water Treatment Equipment is listed under Environmental Protection Equipment. |
| Measured or handled scope | UF / RO / NF / EDI / Softening / Deep treatment |
| System position | Pretreatment and filtration / UF / RO / NF membrane unit / EDI or softening section where required / Pump and control system / Water quality monitoring points |
| Selection basis | Final model, range, accessories and specifications are confirmed by sample medium, target parameters, installation condition and project requirement |
Configured around the actual treatment route
The treatment route is confirmed from the supplied equipment material, then sized by air volume, water volume, pollutant type, material requirement and site layout.
Project-specific wastewater, exhaust gas or pollution control applications
Air volume, water volume, pollutant type, temperature, humidity, corrosion and inlet condition affect configuration.
Treatment body, fans, ducts, pumps, control cabinet, safety protection and maintenance access are reviewed by route.
Hard parameters are kept to supplied product material; final sizing is confirmed by project condition.
Selection notes kept separate from source parameters
Huisheng reviews the treatment route, handled medium, capacity, material, outlet target and auxiliary systems before confirming a configuration. Documented values remain in the technical data table, while project pairing and monitoring-interface notes are treated as selection guidance.
Hard values are kept to the supplied product material. Project-specific sizing is treated as selection work, not as a new published parameter.
Exhaust gas, dust, odor, flue gas polishing or wastewater condition should be confirmed before choosing the treatment route.
Air volume, water volume, pollutant load and outlet requirement determine final equipment sizing.
Q235, 304 stainless steel, FRP, PP or anti-corrosion options are selected according to the documented material scope and site condition.
Fans, ducts, pumps, control cabinets, safety protection and monitoring interfaces are discussed as configuration notes.
Parameters and scope stated in supplied material
The items below summarize capacity, material, process route, efficiency or equipment-scope information from the supplied product material. Extra project advice stays in selection notes instead of becoming a published hard parameter.
UF
Ultrafiltration membrane stage for suspended solids, colloids and pretreatment before deeper purification.
RO
Reverse osmosis desalination stage selected by feed water quality, recovery target and product water requirement.
NF
Nanofiltration stage for partial desalination, organic removal or hardness reduction in selected water routes.
EDI
Electrodeionization polishing stage for high-purity water systems after RO pretreatment.
Softening
Hardness-removal route used before boilers, membranes or process water systems where scaling must be controlled.
Deep treatment
Advanced polishing stage selected after the main water-treatment route to meet reuse or discharge targets.
How the equipment fits into a treatment route
Treatment equipment is configured by process route, pollutant type, air or water volume, material requirement and installation condition. Monitoring or sampling interfaces are considered only when the project needs them.
Pretreatment and filtration
Pretreatment protects the analyzer and helps keep measurement conditions stable.
UF / RO / NF membrane unit
This part is configured according to the selected model and actual site conditions.
EDI or softening section where required
This part is configured according to the selected model and actual site conditions.
Pump and control system
This part is configured according to the selected model and actual site conditions.
Water quality monitoring points
This part is configured according to the selected model and actual site conditions.
Where this equipment is usually discussed
This equipment is discussed when the project needs monitoring or supporting treatment equipment matched with the actual site, medium, parameter and reporting requirement.
Suitable for distributed water points where physical, nutrient or chemical indicators need continuous observation.
Used where discharge quality, treatment stability or final outlet trends need to be followed with clearer online data.
Suitable for distributed water points where physical, nutrient or chemical indicators need continuous observation.
Suitable for distributed water points where physical, nutrient or chemical indicators need continuous observation.
